Get leads

Flake floor leads

Flake floor leads are homeowners who want a chip or flake coated floor, usually in a garage. Ours go to one contractor only, so you're the only crew in the conversation. Guaranteed.

Who asks for a flake floor?

The flake floor buyer wants a garage that looks finished and stays looking clean. The speckled look hides dirt, tire marks and dust better than a solid color. Many saw a neighbor's floor or a photo and want "that."

What they rarely know is that flake floors aren't all the same. A light sprinkle of chips over a thin coat and a full broadcast system look similar in a photo. They don't look or wear the same on the floor.

What makes a flake job different?

A flake floor is a system: base coat, chips broadcast into it, scrape and vacuum, then a clear topcoat. The choices inside that system decide the price and how long it lasts:

  • Partial vs full broadcast. A light broadcast leaves the base showing between chips. A full broadcast covers it completely and builds more thickness.
  • Chip size and blend. Smaller chips give a tighter granite look. Bigger chips read bolder. Color blends are where the homeowner gets excited.
  • Topcoat. The clear coat takes the wear. Many crews use polyaspartic or polyurethane here.
  • Texture. More chips under the topcoat means more grip. Some homeowners want it smoother, some want more traction.

Why does an exclusive lead matter for flake floors?

Because the cheap version looks almost the same on a phone screen. When four crews quote one homeowner, the light-sprinkle bid usually wins on price. The homeowner can't see the difference until it wears.

When nobody else is calling, you can bring chip samples, show the difference in hand, and sell the full system. The homeowner picks colors with you instead of comparing numbers.

Get flake floor leads in your area

Every lead goes to you and nobody else. Guaranteed.

Enter your name.

Enter a 10-digit US phone number.

Enter the city you work in.

By sending this, you agree Epoxy Meta may call and text you about leads at this number. Message and data rates may apply. Reply STOP to opt out. Privacy

What should you ask on the first call?

  1. How many car bays, and what's on the floor now?
  2. Have they seen a flake floor they liked? Where?
  3. Any color ideas? Do they want it to match cabinets or the house?
  4. Cracks, oil spots or damp areas?
  5. Do they want the coating up the stem walls?

Ask them to send a photo of the floor if they can. It saves a trip and tells you a lot.

What do you bring to the walkthrough?

  • Chip samples or sample boards. Let them hold two or three blends. People buy what they can touch.
  • Photos of your full broadcast floors. Close-ups next to a light broadcast make the case for you.
  • A moisture meter or plastic sheet. Same rule as any coating: a wet slab ruins good work.
  • Your three options. Write them down. Good, better, best.

How do you handle "the other quote was a lot less"?

Ask what the other quote included. Was it a full broadcast? What topcoat? Was there a grind? Most of the time the cheaper number skipped something. Point to it calmly. Then hand them the sample board again.

If they're still set on the lowest price, it's fine to let it go. You'll get a better job from the next lead.

How do I start?

Fill in the short form with your name, phone and the city you work in. We call you back. Cost depends on your area and the jobs you want, and we cover it on the call. Flake buyers often ask for fast installs, so polyaspartic leads is worth a look. For general garage work, see garage floor coating leads.

Questions

Are your flake floor leads shared?

No. Each lead goes to one contractor only. We guarantee it's never sent to anyone else.

Where do the leads come from?

We run the advertising that finds homeowners in your area who want a coated floor. You don't run or manage any ads.

Should I quote a flake floor over the phone?

Give a range if they push, then book the walkthrough. Prep, cracks and moisture change the price, and seeing the chip samples is what sells the full system.

What's the easiest upsell on a flake job?

Coating up the stem walls, and a stronger topcoat. Both are easy to explain and easy to see.

How much do the leads cost?

It depends on your area and the jobs you want. We go over it on a quick call. For pricing your own jobs, see how to price epoxy flooring jobs.

Get epoxy leads nobody else gets.

Leave your name, phone and city. We call you back and get you set up.

Get leads in your area

Name, phone and city. We call you back.

Enter your name.

Enter a 10-digit US phone number.

Enter the city you work in.

By sending this, you agree Epoxy Meta may call and text you about leads at this number. Message and data rates may apply. Reply STOP to opt out. Privacy

Get leads in my area